The Tinymight 2 gives you fine control over your experience through a simple analog dial. There is no single “correct” temperature - it depends on whether you are chasing flavour or clouds. Here is how to think about it.
| Range | Character | Best for |
|---|---|---|
| 160-180°C | Maximum flavour, light vapour | Daytime, taste-first sessions |
| 180-200°C | Balanced flavour and density | The all-round sweet spot |
| 200-220°C | Dense clouds, stronger effect | End of session, evenings |
How the dial works
The dial has 10 numbered steps with half-steps in between - roughly 20 settings across a 120-240 °C range. The electronics regulate the heater in real time with high accuracy, so the temperature you set is the temperature you get.
Finding your range
- Lower settings - flavour first. Toward the bottom of the dial the vapour is cool, light and full of terpene flavour. Ideal for tasting a fresh strain and for gentle, aromatic draws.
- Middle settings - the balance. The sweet spot for most people: a good balance of flavour and visible vapour, comfortable and repeatable.
- Higher settings - density. Toward the top the Tinymight 2 produces thick, satisfying clouds and maximum extraction. Vapour gets warmer here - a cooling stem or water pipe helps a lot (see below).
Beast Mode
In On-Demand mode, turn the dial to maximum and keep going until the lights turn white. You have unlocked level “12” - the hottest, most powerful setting, recommended especially for concentrates and for a strong finishing hit.
On-demand vs session temperatures
In On-Demand, the heater only runs while you hold the button, so you can comfortably run a little hotter for quick, dense hits. In Session, heat is applied continuously, so many people dial back a step or two to keep the draw smooth over several minutes.
Fine-tuning: the calibration trick
If the whole dial feels too hot or too cool for your taste, the Tinymight 2 lets you shift the entire range by −3 to +3 steps. For example, a +3 calibration means you reach at level 7 what you previously got at 10. The six steps, from the manual:
- Open and close the battery lid.
- Turn the dial to 0 and triple-click the button. The lights at the bottom flash for a moment; wait a couple of seconds.
- Repeat that step four times.
- Turn the dial to 6 and triple-click. The unit vibrates continuously and shows a green light at the back.
- Turn the dial to choose the range: 6 (green) is the default, 10 (white) the hottest, 0 (blue) the coolest.
- Press and hold the button for about 5 seconds until the vibrations stop, release, and turn the unit off with a triple click.
From then on the unit flashes the colour of the chosen range for a moment when you turn it on. The same steps, with the drawings, are in the operating instructions.
Warmer vapour? Add cooling
At the top of the dial, a longer or ball-style cooling stem, a 3D stem or a water-pipe adapter transforms comfort. See our accessories & cooling guide for the options.
Related: complete guide · cleaning guide.
See the Tinymight 2 →The dial levels in degrees
| Level | Temperature |
|---|---|
| 0 | Lock (the unit will not start) |
| 1 | 140 °C / ~290 °F |
| 2 | 150 °C / ~310 °F |
| 3 | 160 °C / ~330 °F |
| 4 | 170 °C / ~345 °F |
| 5 | 180 °C / ~360 °F |
| 6 | 190 °C / ~380 °F |
| 7 | 200 °C / ~395 °F |
| 8 | 210 °C / ~410 °F |
| 9 | 220 °C / ~430 °F |
| 10 | 250 °C / ~490 °F, session mode limited to 230 °C / ~450 °F |
Was this page helpful?
Still have a question?
